컴퓨터 조립할 때 사용하는 니퍼 (케이블 타이 커팅용으로 좋음)

https://blog.naver.com/PostView.naver?blogId=dongtancom&logNo=222301893031&categoryNo=43&parentCategoryNo=0&viewDate=&currentPage=4&postListTopCurrentPage=1&from=postView 

컴퓨터 조립시 (선정리) 주로 사용하는 니퍼

 

[알리 구입 링크] 

 

https://www.aliexpress.com/af/YTH%25252d23.html?d=y&origin=n&SearchText=YTH-23&catId=0&initiative_id=SB_20210706171102 

YTH-23 - Buy YTH-23 with free shipping on AliExpress

컴퓨터 조립할 때 주로 사용하는 도구 = 날이 작은 니퍼

 

2023년 이 제품으로 사용하는 중입니다.

---

(I thought Naver wouldn't like it if I put the alert link right away, so I put the Naver shopping link instead.)

 

​

 

​

 

​

 

​

 

​

 

The price is low and the blade is sharp, so the plastic (cable tie) is cut well.

 

(I didn't find out if they sell it at domestic shopping malls. It's good to have it delivered free of course. Search word YTH-23

 

It's a disadvantage that it takes a long time to deliver, but if you wait for about a month after ordering, 99% of the delivery will be delivered.)

 

​

 

​

 

​

 

​

 

Computer screws and laptop screws are not loosened. When I held the knife blade and turned it, the blade strength is not high enough to crush it. I don't think there'll be a big problem if it's only used to cut cable ties. Still, if you cut a lot, the blade becomes dull compared to the first time you receive it. It's cheap, so I order and use it every three to six months.

 

​

 

​

 

​

 

If you want to sharpen the blade, you can also sharpen the blade with a nail grinding machine (mini grinder with electric motor) used in the nail shop. I want to buy a mini grinder. Sometimes the screw thread on the laptop is broken, so I think I'll trim the screw head and open it with a flat-blade screwdriver. (Jobbing)

 

​

 

​

 

​

 

There were times when the rubber of the nipper handle came off, but if you put strong adhesive on the handle and put it back on, it rarely comes off.

 

 

YTH-23

 

​

 

​

 

​

 

​

 

​

 

​

 

In the past, I used a thick nipper like below... It's not good for detailed work because the blade is thick. For example, when cleaning the front panel wires, when cutting cable ties, if you cut them incorrectly, they can be cut to the wire. It's better to cut thin and thin than a thick nipper to cut without cutting the line. Rather than cutting the cable tie vertically, if you cut it by laying it down with a small nipper, it's good to cut only the cable tie.

 

 

It's an old nipper, but the blade is strong even though it's old. It's rusty, so you have to oil it in the middle.

 

​

 

​

 

​

 

​

 

​

 

​

 

​

 

​

 

[Related article] Computer repair work tool

 

​

 

Sometimes you need a saw.

 

https://blog.naver.com/dongtancom/222144372077

 

 

My dad wants me to turn off the CPU cooler. I'm in trouble.

When fixing the CPU cooler, if it doesn't turn properly, you should stop tightening it, but if it's tightened with all your strength...

 

blog.naver.com

 

I change the nipper often because I use it often, but I barely remember buying a new long rose.

 

https://blog.naver.com/dongtancom/220687480210

 

 

How to easily remove an Intel CPU fan if it is stuck on the motherboard and cannot be removed

This is the main board that came in with the graphics card PCI-E slot broken while removing the graphics card. So, the main vocalist...

 

blog.naver.com

 

​

 

Nail scissors can also be a good tool for repairing computers.

 

https://blog.naver.com/dongtancom/221315451466

 

 

Making soft work tools with nail scissors

Do you usually use nail scissors to remove the battery on the main board? Like a bent CPU pin or a main board pin.

 

blog.naver.com

 

​

 

​

 

​

 

Sometimes you need an awl.

 

https://blog.naver.com/dongtancom/220091705689

 

 

Pulling out the plastic fixing pins embedded in the PS2 (keyboard) port (you can see it in the picture.)

This is the customer who visited the PS2 port because the fixing pin (plastic?) of the keyboard PS2 was stuck in a damaged state. (...)

 

blog.naver.com

 

​

 

The nipper I used in 2016

 

https://blog.daum.net/dongtancom/131

 

 

[Computer work tools] Nipper suitable for cutting cable ties (Ripper, Nipper)

Usually, nippers use large heads (most commonly found in marts, etc.) The cutting power is good because the head is large, but the head is small like above to cut in detail.

 

blog.daum.net

 

​

 

​

 

https://cafe.naver.com/rpartnerhub/9902

 

 

Stella Mini (improvement plate) front USB header comes out easily and nipper

http://prod.danawa.com/info/?pcode=6400768 (I don't know if it's an improvement) There is a problem that the cable comes off easily as shown below, so I guess something has changed...

 

cafe.naver.com

 

​

 

​

 

[Additional information on January 18, 2023] This is a nipper that I'm currently using. One YTH-101 has a Japan sign and one without a Japan sign. I think it's the same product, so I ordered one separately.

 

 

​YTH-101

 

The blade is weak because it is a low-cost model of 4,000 won to 5,000 won. Cutting plastic like cable ties doesn't hurt the blade, but the steel is nipper-bladed. And it's good to cut when the tip is sharp, but the tip is bent. It's not a good product, but it's a product that can be used for cost-effectiveness. If I find a product that is similar, better, and doesn't break the blade, I'll use it, but I couldn't find it.

 

 

 

 

Nipper broke me.

 

And since the rubber handle is separated from iron, I used iron and rubber as glue for a moment. If you press the nipper while working, the rubber will be pushed out, so I glued it and used it. If you glue it on, it hardly comes off. The size is small and the tip of the nipper blade is sharp, so when you cut the cable tie, the cable can be cut without chewing, so I'm using it well for work. You can buy it directly from Ali or search YTH-101 on Naver Shopping.

 

 

 

 

Knipper handle out - Use instant glue to fix.

 

​