컴퓨터 본체에 하드디스크 5개 장착 (5 hard disks on the computer.)

하드디스크 5개 장착하기

 

몇년동안 사용하지 않던 본체를 수리받아가셨습니다. 하드디스크 및 SSD를 5개 장착해달라는 요청이 있었습니다. 메인보드에 사타 슬롯이 있는 갯수만큼 추가가 가능합니다. 더 많은 사타 장치를 연결하기 위해서는 PCI형태의 SATA확장카드가 있기는 합니다. (ehdxkszjavbxjtnfl)

 

 

 

https://blog.naver.com/dongtanpc/222552441371

 

동탄 컴퓨터 업그레이드 - 삼성 M.2 SSD 업그레이드 후 하드디스크 5개 추가 장착

 

---

It is an old computer made around 2015-2016. It is a computer that was assembled and used with high specifications enough to be used for active duty. There was a problem, so he didn't use it for a while and then visited me to use it again. Perhaps there was a problem such as poor memory connection. In the store, it's working well. However, two SSDs were tied up and used in RAID0. There was a problem that the booting went very slowly. As it is almost impossible to proceed, only the Windows 7 logo has been displayed. Later, I connected the existing SSD to my computer and checked it. The SSD's speed was not working properly, so it seems to have been that slow. The slowed SSD recovered to a normal speed by restarting the factory initialization (format).

 

​

 

The main board is equipped with a high-end main board called GA-Z97X-Gaming 7. You wanted to use the M.2 slot because there was an M.2 slot. Unfortunately, NVMe-type MV2 SSD is not recognized. Only M.2 SSDs using SATA interfaces are normally recognized. We also cleaned up the hardened summer on the CPU and re-applied a new thermal compound.

Re-application of Summer Compound.

 

The existing thermal copper had almost hardened because it had never been re-applied for five to six years. I wiped it off with an alcohol swap. It was hard to scratch even if I scratched it with my fingernails, but it was quickly cleaned after melting it gently with an alcohol swap.

 

How to remove the hardened thermal compound under the water cooler.

 

Samsung 860 EVO SATA M.2 SSD has been upgraded and replaced. I installed the window as a genuine product because you were using the genuine Windows 10 Home Edition.

 

Samsung 860 EVO 500G SSD M.2 SATA

 

The test speed before initialization. It's being measured as low as 10MB/s. It soon appears that the white dot is in poor condition.

 

SSD speed has slowed down.

 

My inspection computer initializes the SSD, which was previously tied up in radii, and then retesting the disk. The speed was not good before initialization, but after initialization, the inspection was completed quickly.

 

It returned at normal speed after factory initialization.

 

​

 

First of all, we remove the graphics card and install Windows 10 to see if the CPU and memory/mainboard operate normally only with built-in graphics. After completing the Windows 10 installation, connect the graphic card to check whether it is operating normally or not.

 

I'm checking if the computer is operating normally.

 

After connecting the graphics card and completing the Windows 10 update, we are connecting the existing SSD and hard disk. A total of 5 storage devices were connected, 4 SSD and 1 HDD.

 

It is equipped with a total of 4 old SSDs (120 gigabytes + 240 gigabytes) + 1 terra hard disk.

 

Existing Sata cables are old products, so we removed them all and replaced them with new Sata cables.

 

We discarded the existing Sata cable and replaced it with a new Sata cable.

 

This main board cannot use some Sata ports if it uses an M.2 SSD slot. Below is an excerpt from some of the manuals.

 

​

 

It is said that if you install the M.2 SSD, the ports No. 4/5 of SATA3 will be deactivated.

 

M.2 SSD slots disable some Sata ports.

 

​